ALC655 allows the board to attach 4 or 6 speakers for a better surround sound effect. 5.1 Channel Audio Effects The motherboard is equipped with the Realtek ALC655 chip, which provides support for 6-channel audio output, including 2 front, 2 rear, 1 center and 1 subwoofer channel. S/PDIF_Out Connector (optional): SPDIF_OUT The S/PDIF out connector is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby digital decoder.ġ2. Speaker Connector: SPEAKER The speaker connector is used to connect speaker of the chassis.ġ1. If you do not want to use the Front Audio, pin 5 and 6, pin 9 and 10 must be SHORT, and then the signal will be sent to the rear audio port.ġ0. If headphones are plugged into the front panel of the chassis (using the Front Audio), then the Line-out (Rear Audio) on the rear panel will not work. Their priority is sequenced from high to low (Front Audio to Rear Audio). Front Audio Connector: F_AUDIO The audio interface provides two kinds of audio output choices: the Front Audio, the Rear Audio. CD_IN Connector: CD_IN CD_IN is Sony standard CD audio connector, it can be connected to a CD-ROM drive through a CD audio cable.ĩ. Compared to traditional USB 1.1 with the speed of 12Mbps, USB 2.0 has a fancy speed up to 480Mbps, which allows faster Internet connection, interactive gaming, and simutaneous running of high-speed peripherals.Ĩ. USB Header: F_USB1 The USB header is available for additional USB port if the USB ports on the rear panel are inadequate. Before using this function, configure the settings of IR Mode from the “Integrated Peripherals” section of the CMOS Setup.ħ. IrDA Header (optional): IR The connector supports wireless transmitting and receiving device. Connect the case cooling fan connector to FAN1.Ħ. CPU FAN & FAN1 Plug the CPU cooling fan cable into the 3-pin CPU FAN power supply on the mainboard. Front Panel Connector: FP1 Attach the power LED, IDE LED, reset switch and power switch connectors to the corresponding pins.ĥ. You will be unable to flash the BIOS to the motherboard when the system BIOS is protected.Ĥ. BIOS-Protection Jumper (optional): FWH_EN If the jumper FWH_EN set as “Disable” (pin2 & pin3), the system BIOS is protected from being attacked by a serious virus, such as the CIH virus. Return the jumper setting to normal (pin2 and 3 together with the jumper cap). Turn off the AC power supply and connect pin 1 and 2 together using the jumper cap. To clear the CMOS, follow the procedures described below. Clear CMOS Jumper: CLS_CMOS You can clear CMOS to restore default system setting. In 6-Channel mode, the function of the three jacks becomes Rear Speaker Out, Front Speaker Out and Center/Subwoofer Speaker respectively.Īccessory Checklist K7S741MG/K7S741GXMG Motherboard (x1) WinFast Utility CD (x1) Easy Installation Guide (x1) IDE Ribbon Cable (x1) FDD Ribbon Cable (x1) I/O Shield (x1)ĬPU: K7S741MG: Supports AMD K7 Duron, Athlon, Athlon XP Supports 266/333/400 MHz FSB K7S741GXMG: Supports AMD K7 Duron, Athlon, Athlon XP Supports 266/333 MHz FSB
The Line-out jack is for a headphone or a speaker. The Line-in jack is for a tape player or other audio sources.
Use the three audio ports to connect audio devices. Line-in jack, Line-out jack, Microphone jack 7 LAN Connector This port allows connection to a Local Area Network (LAN) through a network hub.
#Foxconn n15235 bios reset serial#
USB 2.0 Ports These four Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. The VGA connector is for output to a VGA-compatible device.
Parallel Port (Printer Port) This 25-pin port connects a parallel printer, a scanner, or other devices. Serial Port (COM1) This 9-pin COM1 port is for pointing devices or other serial devices. This purple 6-pin connector is for a PS/2 keyboard. PS/2 Mouse Connector This green 6-pin connector is for a PS/2 mouse. K7S741MG/K7S741GXMG Rear Panel 4 Parallel Port (Printer Port) Remark: The above motherboard layout is provided for reference only please refer to the physical motherboard. Easy Installation Guide K7S741MG/K7S741GXMG LayoutĤ62-pin CPU Socket SiS 741/741GX Chipset USB2.0 Connector CPU FAN Connector SiS 963L ChipsetĬlear CMOS Jumper IR Connector (optional) BIOS-Protection Jumper (optional) Front Panel SYS FAN SPEAKER ATA 66/100/133 FDD Connector Connector Connector Connector IDE Connectors
0 kommentar(er)
